Gas Furnace Faults Found Before the Cold Sets In
Gas Furnace Repair & Installation in northern georgia for failed igniters, burner faults, and homes replacing aging heating equipment
A worn igniter or failed flame sensor typically goes unnoticed until the furnace attempts its first heating cycle of the season, which is exactly when the failure is least convenient. RSK Heating & Air repairs and installs gas furnaces for homes in Northern Georgia. Gas igniter repair and replacement is part of the standard repair scope rather than a separately priced add-on, and the same crew that handles igniter and burner work also performs the safety checks on venting and flue that are required before any repair is considered complete.
Every repair begins with a safety inspection of the gas supply, flue, and venting before any component is tested under live operation. The igniter, flame sensor, and limit switches are then tested while the system is running, so the failure is confirmed under the actual operating conditions that triggered it rather than simulated on a bench. For new furnace installations, RSK sizes the unit with a load calculation for the specific house before any equipment is selected, and the crew connects gas and venting to code, then runs the system through a full heating cycle with combustion checked before handing it over.
Set up a furnace diagnostic visit before the heating season starts so faults are identified while the system can still be tested under load.
The Difference Between a Safety Check and a Basic Repair
Gas furnace work carries a different obligation than other HVAC repairs because a flue or venting fault can produce a hazard that is not visible to the homeowner and does not show up in the system's operating behavior. RSK's repair sequence addresses the gas supply, flue, and venting first, before the igniter or flame sensor is touched, because a cracked heat exchanger or blocked flue changes what the correct repair is. Testing the ignition system under live operation rather than replacing parts by symptom is what distinguishes a diagnostic repair from a parts-replacement visit.
After a repair, the furnace should ignite consistently on the first call for heat, maintain a stable flame through the full heating cycle, and shut down cleanly when the thermostat is satisfied. After a new installation, RSK runs combustion analysis and checks the temperature rise across the heat exchanger before the job is closed, confirming that the new unit is operating within its designed parameters rather than only that it produces heat.
RSK Heating & Air is family-owned and EPA certified, and new furnace installations are sized to the home rather than selected to match the capacity of the unit being removed. Homes in the Southside and Statesboro areas often have older equipment that was sized to general rules rather than a calculated load, and replacing a wrongly sized furnace with the same size repeats the original performance problem.

Questions Before Starting Your Project
The following questions address how gas furnace repair and installation work in practice, including what safety checks are involved and what the installation process covers from start to finish.
Why does the safety inspection happen before the igniter or flame sensor is tested?
The venting and flue condition determines whether the combustion gases from a repaired furnace will be properly exhausted. A blocked or deteriorated flue can cause carbon monoxide to enter the living space even when the furnace ignites and burns correctly, so the venting is checked before live operation testing begins.
How is the igniter tested under live operation rather than off the system?
RSK checks the igniter's resistance before startup and then monitors its surface temperature during the ignition sequence using a clamp meter and temperature probe on the gas valve circuit. This confirms whether the igniter is reaching the temperature required to open the gas valve under the actual voltage the system delivers, not the voltage measured at the panel.
What does a furnace load calculation account for in an older home?
The calculation measures the home's heating demand based on square footage, ceiling height, insulation levels, window area, and duct condition. In older Savannah-area homes where insulation was added after original construction or where room additions changed the floor plan, the calculated load often differs substantially from the original equipment's capacity rating.
What is checked during the combustion analysis at the end of a new installation?
RSK measures the temperature rise across the heat exchanger and compares it to the furnace manufacturer's specified range, checks CO levels in the flue gases, and verifies that the gas pressure at the manifold matches the unit's rated input. These readings confirm the new furnace is burning correctly and not producing excess carbon monoxide under normal operation.
How do you know whether a furnace repair is holding after the technician leaves?
The furnace should ignite on every call for heat without a delay, maintain a steady burner flame through the full cycle visible through the sight glass, and produce supply air temperature within the manufacturer's specified temperature rise range above the return air temperature entering the unit.
RSK Heating & Air also repairs and installs gas furnaces in Northern Georgia. To arrange a diagnostic visit or discuss a new furnace installation, call RSK Heating & Air at (912)6064855 with a description of what the system is doing and when the problem first appeared.