Heat Pumps Diagnosed Before Any Part Is Ordered
Heat Pump Repair & Replacement in collins and the surrounding areas for failed defrost cycles, reversing valve faults, and systems that stop heating entirely
A heat pump that stops heating can quickly leave a home uncomfortable, especially when it is the primary source of heat. RSK Heating & Air provides heat pump repair and replacement throughout Collins and the surrounding areas, servicing the outdoor unit, indoor air handler, and the controls that allow the system to switch between heating and cooling. Regular maintenance can also help catch issues with defrost cycles, refrigerant levels, and overall system performance before they lead to a complete breakdown.
Every repair begins with a full diagnostic on both the outdoor unit and indoor air handler before any part is quoted. RSK checks refrigerant charge, the reversing valve, defrost control board, and all electrical components under live operation, so the actual cause of the failure is confirmed rather than assumed from the symptom. When replacement is the right answer, the new unit is sized with a heat load calculation for the specific home before equipment is selected.
Schedule a diagnostic visit to identify exactly which component is responsible for your system's current behavior.
How Heat Pump Diagnosis Drives the Right Repair
Heat pump failures are frequently misread because several different faults produce similar symptoms. A system running in emergency heat mode due to a reversing valve failure looks nearly identical from inside the house to a refrigerant charge issue or a failed defrost board. RSK's diagnostic sequence checks each component in order, testing the reversing valve operation and defrost cycle timing directly rather than relying on error codes alone, which allows the correct part to be identified before the repair is quoted.
After a repair is complete, the system should maintain setpoint temperature through both heating and cooling cycles without extended runtime or auxiliary heat activation at moderate outdoor temperatures. After a full replacement, RSK sets, charges, and tests the new system in both heating and cooling modes before the job is closed, so the homeowner has confirmed operation in both directions rather than only the mode needed on the day of installation.
RSK Heating & Air is family-owned and EPA certified, and replacement sizing is handled with a load calculation for the specific house rather than matching the tonnage of the unit being removed. An undersized replacement will short-cycle in cooling and struggle at low temperatures; an oversized unit will fail to dehumidify properly and wear its components faster than a correctly sized system would.

Common Questions About This Service
The following questions address how heat pump repair and replacement work in practice, including what the diagnostic covers and what proper installation involves.
What does the heat pump diagnostic actually check?
RSK checks refrigerant charge with gauges, tests the reversing valve for proper switching between heating and cooling modes, evaluates the defrost control board's timing and activation, and inspects all electrical connections and contactors under live operation before any part is identified for replacement.
Why does a failed reversing valve leave a home with no heat?
The reversing valve is the component that shifts refrigerant flow direction, which is what allows a heat pump to extract heat from outdoor air in winter. When it fails in the cooling position, the system continues to run but moves heat in the wrong direction, producing cool air at the supply registers regardless of the thermostat setting.
How is replacement sizing handled differently from a repair?
Repair sizing is not a factor, but replacement requires a heat load calculation that accounts for the home's square footage, insulation levels, window area, and duct condition. Homes in the Savannah area that were built before current insulation standards may require a different capacity than the original unit to maintain comfort without excessive runtime.
What happens during the installation of a replacement heat pump?
RSK removes the old outdoor and indoor units, sets the new condenser and coil, connects and pressure-tests the refrigerant lines, wires the system to the air handler and thermostat, charges the refrigerant to the manufacturer specification, and runs the system through both heating and cooling modes before completing the installation.
How can you tell whether a heat pump repair is holding after the technician leaves?
The most reliable indicators are consistent supply air temperature at the registers, the system reaching setpoint without activating the auxiliary heat strip at moderate outdoor temperatures, and the outdoor unit cycling through its defrost routine without freezing over or locking out on high pressure.
RSK Heating & Air also repairs and replaces heat pumps in collins, Vidalia, Lyons, Reidsville, and beyond. To set up a diagnostic on your outdoor unit and air handler, call RSK Heating & Air at (912)6064855 and describe what the system is doing so the crew arrives with the right test equipment.